The feed mixing machine is a mechanical device that uniformly mixes two or more materials through mechanical force, gravity, and the like. During the mixing process, the surface contact surface area of the material can increase to promote chemical reactions. Physical changes can also accelerate. Fusmar is a professional animal feed mixer manufacturer, this article will introduce a common feed mixing machine in detail.

Common Animal Feed Mixer

The feed mixer, whether it is the production of powder or the production of pellets, it all can use. It is a commonly equipment in feed processing machinery. However, there are many types of feed mixers on the market. Which feed mixer is suitable for farmers? Different sizes have different requirements for feed mixers. How do you find a feed mixer that suits you? Here are some common feed mixers.

Vertical Crushing And Mixing Machine

The vertical crushing and mixing machine referred to as an all-in-one machine. It is a favorite feed mixing device for small farmers. Because of its cover a small area, strong function, and low cost, many farmers choose to use this. With the continuous development of feed processing machinery, the vertical crushing and mixing machine has also been upgraded. The upgraded version of the dust-free feed crushing and mixing machine has done a better job in environmental protection and is more suitable for the current breeding environment.

Single Shaft Double Spiral Feed Mixer

The single shaft double spiral feed mixer, also known as the horizontal ribbon feed mixer. It is favored by feed mills and medium-sized farms because of the fully open-top feed port. Which can use with various powder feed machine or feed pellet machine. Therefore, many large and medium-sized feed pellet production equipment often see the horizontal feed mixer. Compared with the vertical crushing and mixing machine, it has a faster mixing speed and a higher output.

U Type Horizontal Feed Mixer

U type horizontal feed mixer adopts a U-shaped barrel structure, which has a stable operation, uniform mixing, no dead angle, clean discharge, and wide application range. The materials thoroughly mixed to increase mixing uniformity. Adopting the novel rotor structure, the minimum clearance between the rotor and the casing can adjust to near-zero position, effectively reducing the amount of material residue. The machine equipped with a grease adding pipeline, the overall structure is more reasonable. The appearance is beautiful, and the operation and maintenance are convenient. This machine has the characteristics of high strength, compact structure, wear resistance, low energy consumption, long service life, and convenient operation and maintenance.

Drum Type Feed Mixer

The drum type feed mixer has a high mixing uniformity, but the loading and unloading port are inconvenient because it is suspended. The time to mix a batch of material is also relatively long. Suitable for dilution mixing of nutrients such as premixes and vitamins.

Choosing A Suitable Animal Feed Mixer

The cost-effective feed mixers suitable for farmers are the vertical crushing and mixing machine and the single shaft double spiral feed mixer. The farmers can choose the feed mixing machine according to their own farm needs and land occupation. Choosing a suitable feed mixing machine and using it properly will significantly improve the quality of the mix. It will soon reflect a benign effect in the production process. If you can further master the technology of self-mixing, you can also greatly reduce the cost of materials, thereby increasing profits.

Zhengzhou Fusmar Machinery specializes in the production of feed hammer mill, feed mixing machine, feed pellet machine, feed cooling machine, feed packing machine, and other feed machinery.

Charcoal Briquette Applications
Charcoal briquette has the advantages of high density,small volume,good flammability, smokfree, tasteless,non-toxic,etc. It’s widely used in heating,BBQ market. In the industry area, it’s the alternative raw material of the coal or heavy oil.
Material Of Charcoal Briquette Production Line
Many material suitable to make the charcoal briquette, if the wood logs are available, they are very suitable to make the charcoal briquette directly. But since the forest resources are limited, and also this will add the cost, so more wood waste, branches, sawdust, agro waste become alternative raw materials. But these materials need some special process before they become charcoal briquette.

Process Of Charcoal Briquette Production Line
1. Crushing the material into granules less than 10mm. Below are the crushing machine for wood logs,bratches,straws,agro waste. 2. Dry the granules to make reduce the mositure between 8%-12%,this process needs special attention. Below are the 2 styles dryer for different capacity. The air flow dryer usually match small capacity production line, for large capacity line it can’t reduce too much moisture. Rotary dryer is very suitable for large capacity line, and for the material with above 30% or 40% moisture. Because its effect of removing mositure is obvious.  3. Carbonizing the sawdust stick into charcoal briquettes. This process will heat an d burn the stick in the carbonization furnace, in order to save cost, some customers will build the carbonization furnace by themselves.  4. Since the temperature of is very high, the charcoal briquette need cooling for 8-24 hours. 

Flat Die Pellet Machine Introduction
Biomass pellets now are now welcome world wide, it has many advantages compared with the traditional petroleum ,gas,coal,wood,etc. They are renewable and sustainable, cost effective and Eco-friendly. Flat die die wood pellet machine has simple structure,small size and cost less, so it has the advantages of low energy consumption, very good mobility, so it is very suitable for the family workshop.

Flat die wood pellet machine working Principle
The first pellet mill design at the turn of the 20th century based on flat dies. Generally, there are two types of flat die pellet mills in the market, the rotating die type and the rotating roller type. The former one has a stationary roller with the rotating die while the latter has a stationary die with a rotating roller. Adopting vertical principle, the raw materials drops down by the its own weight into the pelletizing chamber where they are compressed between the rollers and die to form pellets by going through the die holes.

Flat die wood pellet machine advantages
1. The Feeding Way. Flat die pellet machine feeds the material into the pressing chamber vertically by the weight of itself. And the process speed is even.
2. The diameter of the roller is out of the limit of the flat die, it can expand the inner bearing space. The bigger bearing not only can increase the endurance of the roller,but also improve the pressing power and prolong its life-span.
3. The Discharging Way, flat die has low rotation speed, then it low rate of spoiled pellets.
4. The roller way adjusting way. Flat die roller can adjust with the thread column by manual rotation or hydraulic automation.

Mainly used for a variety of aquatic products, pet and other pellet feed curing molding process (such as: float and sink of fish feed, frog feed, pellet suckling pig feed).

Dry Fish Feed Machine Working Principle

1. During extruding process, material feed from the end of machine cavity convey to the whole cavity by screw, then divided into several regions at extruded part, each region have a ring (press ring) to control flow and press. Screw convey function drive the material through the gap between the press ring and cavity, screw rotating motion generate energy with the friction between material and extruder parts is transformed into thermal energy.
2. In most cases, the material rich with starch and protein is cooked into a sticky dough or gelatinous dough. During the transform process, the material have a large physical and chemical changes, mainly is the results of starch and protein changes.
   3.When the material is extruded through molding holes at the end of machine cavity, make the dough material processed into a certain shape. Due to the large of propulsive force of screw inside cavity, the material have a huge pressure, when material is extruded from the molding holes, it instantly vaporized a large quantities moisture, greatly reduce the material moisture content.
3. When produce low density products, it would have a large expansion depends on the molecular structure of material, and all condition and material used during extruding process
4. When produce high density products, it would not expansion large depends on the purging pressure port on the cavity and all condition and material used during extruding process.

Zhengzhou Fusmar Machinery Co.,Ltd is a professional fish & animal feed pellet machinery and wood pellet machinery manufacturer. We have our own engineer and sales team to provide best machines and services to our customers worldwide.

Our products mainly include floating feed pellet machine,animal feed pellet machine,feed grinding machine, feed mixer,wood crushing machine,wood chippers,hammer mills,pellet coolers, pellet packing machine,conveyors and other spare parts.